XC6121C716MR-G belongs to the category of voltage regulators.
It is commonly used for voltage regulation in electronic circuits.
XC6121C716MR-G is available in a small package, suitable for surface mount technology (SMT).
The essence of XC6121C716MR-G lies in its ability to regulate voltage levels effectively and efficiently.
XC6121C716MR-G is typically packaged in reels or tubes, with a quantity of 3000 units per reel/tube.
XC6121C716MR-G has the following pin configuration:
XC6121C716MR-G operates by comparing the output voltage with a reference voltage. It adjusts the internal circuitry to maintain a stable output voltage, regardless of changes in the input voltage or load conditions.
XC6121C716MR-G finds applications in various electronic devices and systems, including: - Mobile phones - Portable media players - Digital cameras - Wearable devices - IoT devices
Some alternative models that can be considered as alternatives to XC6121C716MR-G are: - XC6206P332MR - XC6220B332MR - XC6219B332MR - XC6220C332MR - XC6220D332MR
These models offer similar voltage regulation capabilities and package options.
In conclusion, XC6121C716MR-G is a compact and efficient voltage regulator suitable for a wide range of electronic applications. Its small form factor, low power consumption, and high efficiency make it an ideal choice for portable and battery-powered devices. However, its limited maximum output current and restricted operating temperature range should be taken into consideration during design and implementation.
Sure! Here are 10 common questions and answers related to the application of XC6121C716MR-G in technical solutions:
1. What is XC6121C716MR-G? - XC6121C716MR-G is a voltage detector IC (integrated circuit) manufactured by Torex Semiconductor. It is used to monitor the voltage level of a power supply and provide an output signal when the voltage falls below a certain threshold.
2. What is the operating voltage range of XC6121C716MR-G? - The operating voltage range of XC6121C716MR-G is typically between 0.8V and 6.0V.
3. How does XC6121C716MR-G work? - XC6121C716MR-G works by comparing the input voltage with a reference voltage. When the input voltage drops below the reference voltage, it triggers an internal circuit that generates an output signal.
4. What is the output type of XC6121C716MR-G? - XC6121C716MR-G has an open-drain output type, which means it can sink current but cannot source current.
5. What is the maximum sinking current of XC6121C716MR-G? - The maximum sinking current of XC6121C716MR-G is typically 50mA.
6. Can XC6121C716MR-G be used for overvoltage detection? - No, XC6121C716MR-G is specifically designed for undervoltage detection. It triggers an output signal when the voltage falls below a certain threshold.
7. What is the typical quiescent current of XC6121C716MR-G? - The typical quiescent current of XC6121C716MR-G is very low, usually around 1.0µA.
8. Can XC6121C716MR-G be used in battery-powered applications? - Yes, XC6121C716MR-G is suitable for battery-powered applications due to its low quiescent current and wide operating voltage range.
9. Does XC6121C716MR-G have built-in hysteresis? - Yes, XC6121C716MR-G has a built-in hysteresis of typically 100mV, which helps to prevent output oscillation near the threshold voltage.
10. What is the package type of XC6121C716MR-G? - XC6121C716MR-G is available in a SOT-25 package, which is a small surface-mount package with 5 pins.
Please note that the answers provided here are general and may vary depending on the specific datasheet and application requirements.